Part Name/Number Part Image Barrel Nut 1/4" - 20 19-900014 Barrel Nut #10 - 20 19-910004 Black Poly Drive Band 23-400054 Double Drive Bands (3/pkg) 16-970000 …
Prior to your loom delivery, we will send you an email with the tracking information for your shipment. The shipping company will contact you when the loom arrives at their…
Flyer won’t turn. The drive band is not over the flyer whorl, or the drive band is too loose. Make sure the drive band is positioned correctly in the flyer…
My Ladybug makes a clunking noise when I spin. My Ladybug's drive wheel won't turn when I treadle. In the past, some wooden hubs detached from the nylon drive wheel.…
Check to see if your floor is level If you have found that your beater does not come up square to the front beam, the first and most important thing…
Clunking sound while spinning backwards (counterclockwise) If you have an older Sidekick (pre-2016) some wooden hubs were prone to detach from the nylon drive wheel. In some cases the glue…
The end of the heddle bar hook should be approximately 3" from the outside of the harness frame. If your heddles slide freely on the heddle bars you will not…
If your spinning wheel is in good condition, it can be converted to a double treadle. Actual shipping charges for shipping your wheel back to you will be added to…
To fix noisy bobbins use white grease lubricant (available at most hardware stores). Place the bobbin on the flyer shaft. Then place a small amount of white grease on either…
Try to keep the wheel in a dry, moderate climate. Try to avoid temperature extremes (i.e. keep out of direct sunlight and really damp and cold climates). Do not use…
Brake Won't Hold Inspect the brake hub (you don’t need to remove it to do this). If the hub is grooved, the cable will not hold properly. Most often grooves…
Rusty reeds can be cleaned by rubbing out the rust with fine steel wool or by using a commercial rust remover, such as Naval Jelly. When using these products be…
Easy Fixes - Check to make sure that the loom is level. To check level, place a level across the front beam and then the back beam. If the loom…
If the insert in the wood that holds the wheel has somehow been damaged, the stroller wheel might fall out. You can try using epoxy to glue the stem part…
PDF Manual On older Wolf looms, if you completely unscrew the fold knob, the metal t-nut that the knob screws into can slip down inside the castle far enough that…
If the upper shed (raised warps) are uneven: Raise the threads by shortening the lower lamm cord of the errant shaft. If the lower shed (sinking warps) needs to be…
Equipment required: Strong cotton cord (approx 30” for each shaft) and a tapestry needle with eye large enough for the cord. If the loom is not warped, remove the shaft…
1. Measure warp on warping board. 2. Secure warp chain to front beam for threading front to back. 3. With the front of the loom toward you, place a heddle…
First check to see if there is a 1/16" - 1/8" gap between the lip of the flyer and the orifice bearing. If there isn't a gap: Release the front…
We do not buy back used equipment, and are unable to provide information on the value of used equipment since this depends heavily on the condition of the equipment and…
"Four Now - Four Later" (4N4L) is a loom shipped with four shafts installed, and with the capacity to add an additional four shafts. You can purchase a kit to…
Looking down at the loom from above, if the loom has empty channels in the castle, then you can add four shafts. If there are no empty channels, then you…
Manual PDF
Pre 2012 2012 - Present
Single Treadle: Pre 2012 - Metal Support Pre 2012 2012 - Present Double Treadle: Pre 2012 - Metal Support Pre 2012 2012 - Present 40th Anniversary Cherry
Manual PDF
Manual PDF
Assembly Instructions
Wheels 1996 - Current
Manual PDF
